Heat Pump Installation & Repair for Chicago Homeowners
Chicago homeowners are increasingly turning to heat pumps as a smart way to heat and cool their homes with a single efficient system. At Jimco Electric, we provide full-service heat pump installation & repair for homes throughout Chicago and the surrounding suburbs, including Evanston, Berwyn, Oak Park, and Naperville.
Our licensed electricians handle everything from evaluating your existing electrical panel to pulling city permits and completing the final wiring. We work on homes of all ages, including the older two-flats and bungalows common throughout Chicago neighborhoods like Logan Square, Beverly, and Bridgeport.
What’s Included in Our Heat Pump Installation & Repair Service
When you hire Jimco Electric for heat pump work, you get a complete electrical solution, not just a basic install. We handle the permitting, panel evaluation, circuit installation, and system testing so you are covered from start to finish without chasing down multiple contractors.
Dedicated Circuit and Panel Evaluation
Heat pumps require a dedicated electrical circuit, and many Chicago homes built before 1980 do not have adequate panel capacity to support one without upgrades. Our electricians assess your current setup and identify any panel limitations before work begins. If you need a panel upgrade, we handle that as part of the same project.
Permit Procurement and Code Compliance
All heat pump installations in Chicago require electrical permits through the City of Chicago Department of Buildings. Jimco Electric submits permit applications on your behalf and schedules all required inspections. This protects you legally and ensures the installation meets current Illinois electrical code standards.
System Wiring, Testing, and Commissioning
Once permits are approved, our technicians complete all wiring connections to the indoor and outdoor units, install disconnect boxes, and run any new circuits required. We test the system under load before we leave to confirm everything is operating correctly. You receive documentation of all completed work for your records.
Ready to move forward? Call Jimco Electric for a free in-home estimate and we will walk you through the best options for your property.
Signs You Need Professional Heat Pump Installation & Repair
There are several situations where Chicago homeowners should call a licensed electrician for heat pump help. Some are obvious, like a system that stops working in the middle of January. Others are easier to miss until they turn into bigger problems.
Your Heat Pump Is Tripping Breakers or Losing Power
If your heat pump is repeatedly tripping the circuit breaker, that is a sign the electrical supply to the unit is undersized or there is a wiring fault. This is a common issue in older Chicago homes where the electrical infrastructure was not designed to handle modern HVAC loads. Ignoring it can damage the heat pump motor or create a fire hazard.
You Are Replacing an Old Furnace or Window AC Units
Many Chicago homeowners are retiring aging gas furnaces and replacing rooms full of window air conditioners with a single heat pump system. This transition requires new electrical circuits, updated panel capacity, and careful load calculations specific to your home’s size and layout. Our team handles the full electrical side of that conversion. We can also coordinate alongside your HVAC contractor if needed.
Your System Is Running Constantly Without Reaching Temperature
A heat pump that runs non-stop without hitting the thermostat setpoint may have a refrigerant issue, but it can also signal an electrical problem affecting compressor performance. In Chicago’s winter climate, an underperforming heat pump is not just uncomfortable, it drives up energy bills fast. A diagnostic visit from our team can confirm whether the issue is electrical and get your system back on track.
Do not wait for a small problem to turn into a complete system failure, especially heading into a Chicago winter or summer. Call Jimco Electric at the first sign of trouble.
Our Heat Pump Installation & Repair Process for Chicago Homes
Schedule Your Free Consultation
Reach out to Jimco Electric by phone or through our website to set up a free on-site consultation. We serve Chicago and communities up to 40 miles outside the city, so scheduling is convenient no matter where you are located. Our team will confirm your appointment and explain what the visit covers before we arrive.
Evaluate Your Electrical System and Load Requirements
During the site visit, our electrician inspects your current electrical panel, reviews available circuit capacity, and measures the electrical demands of the heat pump system you plan to install. Older Chicago homes, particularly those with 100-amp service, often need a panel upgrade before a heat pump can be safely connected. We document the findings and present a clear scope of work with pricing before moving forward.
Complete the Electrical Installation and Wiring
Once permits are in hand, our licensed technicians run new circuits, install disconnect boxes, and complete all wiring connections to the heat pump system. We follow Chicago building code requirements throughout and coordinate with the City of Chicago Department of Buildings for required inspections. All work is done cleanly and professionally, with minimal disruption to your home.
Test the System and Confirm Safe Operation
After installation is complete, we power up the system and run a full operational test to verify all electrical connections are performing correctly. We check voltage, amperage, and breaker performance under real load conditions. Before we leave, we walk you through the completed work and answer any questions about your new system. For added protection, ask us about whole-home surge protection to safeguard your investment from power fluctuations.
