If half your house suddenly has no power and no breakers are tripped, the most common cause is a lost utility leg, meaning one of the two 120-volt lines coming into your home from the street has failed. This can also be caused by a failing main breaker, a damaged service entrance cable, or a corroded neutral connection. This guide walks through every likely cause, what you can safely check yourself, and when to call a pro in Chicago or the surrounding suburbs.
Understand How Your Home’s Electrical Service Actually Works
Most Chicago-area homes use a split-phase 240-volt service. The utility company delivers two separate 120-volt legs into your main panel, labeled Line 1 and Line 2. Each leg powers a different set of breakers inside your panel.
Standard outlets and lights run on one leg at a time. Large appliances like your dryer, range, or central AC use both legs combined to reach 240 volts. When one leg goes out, exactly half your circuits lose power while the other half stay on.
This is why the problem feels so confusing. The lights in one room work fine, but the next room is completely dark. Your refrigerator runs, but the microwave is dead. It looks random, but it follows a very predictable pattern tied to which leg each breaker sits on inside your panel.
Identify the Most Likely Cause: A Lost Utility Leg
A lost utility leg is the single most common reason half a house loses power with no tripped breakers. This happens when one of the two service wires running from the utility pole to your meter develops a problem.
In Chicago and suburbs like Naperville, Oak Park, and Joliet, overhead service lines are common in older neighborhoods. Ice storms, high winds, and aging insulation can all cause a service wire to break, corrode, or pull loose at the weatherhead connection on your roof.
Underground service areas are not immune either. A dig-in, water intrusion into a conduit, or a failing splice at the transformer can produce the same result. In both cases, the fix belongs to ComEd, not your electrician. Call ComEd at 1-800-334-7661 to report a partial outage before assuming it is an internal wiring problem.
- Check your neighbors: if nearby homes also have partial outages, it is almost certainly a ComEd issue.
- Look at your meter base from outside for any visible burn marks or melted plastic.
- Do not touch the service wires at any point. They carry live utility voltage at all times.
- Call ComEd first. They will send a crew to check the drop at no charge to you.
Recognize When the Main Breaker Is the Problem
If ComEd confirms their lines are fine, the next suspect is your main breaker. A main breaker can fail internally without ever tripping to the off position. This is more common than most homeowners realize, especially in panels that are 20 or more years old.
When a main breaker fails on one pole, it interrupts power to all the branch breakers fed by that pole. The breaker handle stays in the on position, which is why nothing looks wrong from a visual inspection. The breaker simply stops conducting electricity on one side.
Older Federal Pacific Stab-Lok panels and Zinsco panels, both of which are still found in many Chicago-area homes built in the 1960s and 1970s, are especially prone to this type of internal failure. If your home has one of these panels, a failing main breaker is a serious safety concern beyond just the power loss.
- A failing main breaker may also produce a faint burning smell near the panel.
- The panel cabinet may feel warm to the touch even when the room is cool.
- Never try to reset a main breaker repeatedly if it seems unresponsive. Call an electrician.
- Main breaker replacement typically costs between $150 and $300 for the part and labor, depending on the panel brand and amperage rating.
Compare Common Causes at a Glance
Not every partial outage has the same cause. The table below lays out the most common reasons half a house loses power, who is responsible for the fix, and a rough cost range where applicable.
| Cause | Who Fixes It | Estimated Cost | Emergency Risk |
|---|---|---|---|
| Lost utility leg (ComEd service drop) | ComEd | No charge to homeowner | Low (utility side) |
| Failing main breaker | Licensed electrician | $150 to $300 | Medium to high |
| Damaged service entrance cable | Licensed electrician | $500 to $1,500 | High |
| Loose or corroded neutral at meter | ComEd or electrician | $100 to $400 | High |
| Failed main panel bus bar | Licensed electrician | $800 to $2,000+ | High |
A loose neutral is worth highlighting separately. When the neutral conductor at your meter base or service entrance becomes loose or corroded, voltage can shift unevenly between the two legs. This can actually overvoltage appliances on one leg while starving the other. It can destroy sensitive electronics and is a fire risk.
Understand Why This Problem Is Different in Older Chicago Homes
Chicago has a large stock of older housing. Many homes in neighborhoods like Beverly, Jefferson Park, and Bridgeport were built in the 1920s through 1950s. Homes in suburban areas like Berwyn, Cicero, and Blue Island often date from the same era.
These homes may still have original service entrance cables with cloth or rubber insulation that has become brittle over decades. They may have meter bases that have never been inspected since installation. Corrosion and loose connections are far more likely in equipment that is 50 to 70 years old.
At Jimco Electric, we frequently respond to partial power loss calls in older Chicago neighborhoods and find service entrance cables that are cracked, corroded, or pulling away from the weatherhead. These are not cosmetic issues. A damaged service entrance cable can arc, spark, and start a fire inside your wall or attic.
Illinois does not require homeowners to update their service entrance on a fixed schedule, but the National Electrical Code and local Chicago electrical permits do require upgrades when substantial work is done. If you are already dealing with a partial outage caused by aging equipment, it is worth asking your electrician to evaluate the full service while they are on site.
Know What a Repair or Replacement Actually Costs in the Chicago Area
Cost is one of the first questions homeowners ask when something like this happens. The table below gives realistic ranges for common repairs tied to partial power loss in the Chicago metro area, including suburbs within 40 miles of the city.
| Repair Type | Chicago City Estimate | Suburban Estimate (40-Mile Radius) | Typical Timeline |
|---|---|---|---|
| Main breaker replacement (200A) | $200 to $350 | $175 to $300 | 1 to 2 hours |
| Service entrance cable replacement | $900 to $1,800 | $700 to $1,500 | 4 to 8 hours |
| Meter base repair or replacement | $400 to $800 | $350 to $700 | 2 to 4 hours |
| Full panel replacement (200A) | $2,000 to $4,000 | $1,800 to $3,500 | 1 to 2 days |
| Neutral connection tightening or repair | $100 to $250 | $100 to $200 | Under 1 hour |
These are estimates based on typical Chicago-area labor rates and material costs as of 2025. Your actual cost depends on the panel brand, ease of access, whether a permit is required, and whether ComEd needs to disconnect power at the meter before work can begin.
In Chicago, most service entrance and panel work requires a permit from the Chicago Department of Buildings. Suburban municipalities each have their own permit requirements. Jimco Electric handles permit coordination as part of any service entrance or panel project, so you do not have to track that down yourself.
Take These Safety Steps While You Wait for Help
A partial power loss is not always an emergency you can ignore until morning, especially if you notice heat, smell burning, or hear buzzing near the panel or meter. Here is what to do while you arrange for a professional evaluation.
- Call ComEd first to rule out a utility-side problem. Their outage line is 1-800-334-7661 and is available 24 hours a day.
- Do not keep flipping breakers on and off hoping something resets. If the problem is a failing main breaker or a loose neutral, repeated switching can cause arcing.
- Unplug sensitive electronics and appliances on the affected circuits. A neutral issue can cause voltage spikes that damage motors and circuit boards.
- If you smell burning near the panel, meter, or any outlet, leave the area and call 911 before calling an electrician.
- Avoid using extension cords to run power from working circuits to rooms without power. This is a fire risk and puts excess load on the working leg.
- If the panel feels warm or you see scorch marks, treat it as an emergency and do not re-enter the home until an electrician clears it.
FAQs on Half-House Power Loss with No Tripped Breakers
Can a breaker fail without tripping to the off position?
Yes. A breaker can fail internally and stop conducting electricity while the handle stays in the on position. This is especially common with older breakers and is one of the main reasons half a house loses power without any visible trip. An electrician can test this with a voltmeter in a few minutes.
Is a partial power outage a fire hazard?
It can be, depending on the cause. A loose neutral or a damaged service entrance cable can cause arcing, overheating, or voltage irregularities that damage appliances and create fire risk. Do not ignore a partial outage, especially if you notice warmth, discoloration, or smell near the panel or meter.
Will ComEd fix the problem for free if it is on their side?
Yes. If the problem is with ComEd’s service drop, meter socket seal, or transformer, they repair it at no charge to you. Call their outage line at 1-800-334-7661. If the problem is inside your meter base or service entrance cable, that is your responsibility and requires a licensed electrician.
How long does a partial power outage repair usually take?
Simple fixes like a main breaker replacement can take one to two hours. A full service entrance cable replacement may take four to eight hours and may require a ComEd disconnect and reconnect appointment, which can add a day to the timeline. Your electrician can give you a more specific estimate after inspection.
Does a partial power outage mean I need a whole new panel?
Not necessarily. Many partial outages are caused by a single failed component like a main breaker or a loose connection, not the entire panel. However, if your panel is over 30 years old, has a recalled brand like Federal Pacific or Zinsco, or shows widespread corrosion, a full replacement may be the smarter long-term choice.
Can I check the main breaker myself?
You can visually inspect whether the handle is in the on, off, or tripped position, but do not try to open the panel cover or test voltage yourself. The wires inside a main panel carry live voltage even when the main breaker is off, and only the utility company can de-energize those. Leave internal diagnosis to a licensed electrician.
Wrap Up and Next Steps
Half-house power loss with no tripped breakers almost always points to one of three things: a lost utility leg from ComEd, a failing main breaker, or a damaged neutral or service entrance connection. Start with a ComEd call to rule out the utility side, then get a licensed electrician on-site to diagnose what is happening inside your panel.
Jimco Electric serves Chicago and communities throughout the 40-mile surrounding area, including Naperville, Berwyn, Joliet, Oak Park, and beyond. If you are dealing with a partial outage right now, call us at 708-304-8687. We will diagnose the problem, walk you through your options, and get your power restored safely.